George

i have tried to do the encoding, 

But when i reach the ABS module i receive the following error:

I have realized that i have been trying to do the coding with Byte 26 encoded to 11110000 , can this be the problem?3

If i do the rest of the encoding i get the following error in the engine:

Address 01: Engine (J623-CKFC)       Labels:. 04L-907-309-V1.clb
   Part No SW: 04L 906 021 DT    HW: 04L 907 309 D
   Component: R4 2,0L EDC   H22 8127  
   Revision: 83H22---    
   Coding: 111D001A043401091000
   Shop #: WSC 02001 451 00000
   ASAM Dataset: EV_ECM20TDI01104L906021DT 002008
   ROD: EV_ECM20TDI01104L906021DT_002.rod
   VCID: 7A3EB2053FC3E65006-802E

2 Faults Found:
17149 - Check Coding of ECUs on Powertrain Data Bus 
          P1647 00 [032] - -
          Intermittent - Not Confirmed - Tested Since Memory Clear
             Freeze Frame:
                    Fault Status: 00000001
                    Fault Priority: 2
                    Fault Frequency: 1
                    Mileage: XXX km
                    Date: 2018.01.06
                    Time: 16:13:00

                    Engine speed: 0.00 /min
                    Normed load value: 0.0 %
                    Vehicle speed: 0 km/h
                    Coolant temperature: 50 °C
                    Intake air temperature: 52 °C
                    Ambient air pressure: 930 mbar
                    Voltage terminal 30: 12.020 V
                    Unlearning counter according OBD: 40
                    ACC variants-Bit 0: 0
                    CCS Switch-Bit 0: 1
                    Cruise control switch actuation-Bit 0: 0
                    Cruise control switch actuation-Bit 8: 32
                    ACC variants (coding)-Bit 0: 3
                    Acceleration: 0.000 m/sІ

4709 - No Communications with Cruise Control (Front) Distance Sensor 
          U0235 00 [032] - -
          Intermittent - Not Confirmed - Tested Since Memory Clear
             Freeze Frame:
                    Fault Status: 00000001
                    Fault Priority: 6
                    Fault Frequency: 1
                    Mileage: XXX km
                    Date: 2018.01.06
                    Time: 16:12:59

                    Engine speed: 0.00 /min
                    Normed load value: 0.0 %
                    Vehicle speed: 0 km/h
                    Coolant temperature: 50 °C
                    Intake air temperature: 52 °C
                    Ambient air pressure: 930 mbar
                    Voltage terminal 30: 12.020 V
                    Unlearning counter according OBD: 40
                    Drivetrain coordinator: ACC fault status-Bit 0: 0
                    Drivetrain coordinator: ACC fault status-Bit 8: 0
                    Drivetrain coordinator: brake fault status-Bit 0: 0
                    Drivetrain coordinator: brake function status-Bit 0: 0
                    Drivetrain coordinator: brake function status-Bit 8: 0
                    Acceleration: 0.000 m/sІ

Readiness: 0 0 0 0 0 

przed chwilą, rrobert napisał:

Send autoscan from car 

autoscan.txt

7 godzin temu, rrobert napisał:

what type of sensor is the ABS you buyed
try change coding to 11110000 

abs icon in instrument is lighting

Thanks a lot!!! it worked! I coded the ABS to 11110000 and after 7-8 km. of driving it is okay. I will drive more tomorrow and check if there are errors written in the abs module.

I bought sensors  wht003864a from carsequipment. 

When i was having the fault the ABS lamp on the instrument panel was NOT on.

Will the ACC run if i do all the steps without the one with ODIS ?

Hi guys, 

i have changed the rear sensors last weekend and i put the one ending on A. 

But i get the following fault codes:

                Address 03: ABS Brakes Labels: 5Q0-907-379-ESP-V1.clb
Control Module Part Number: 5Q0 907 379 R HW: 5Q0 907 379 F
  Component and / or Version: EMB8 EHCB H31 0356
           Software Coding: 1C07629124210975007D060141C4243846249000608224F0F0615070C002
            Work Shop Code : WSC 73430 031 00063
              ASAM Dataset: EV_Brake1UDSContiMK100ESP 033001 (SK37)
                       ROD: EV_Brake1UDSContiMK100ESP_033.rod
                      VCID: 4BCD144833143CC95E-801E
2 Faults Found:

0070 - Rear Left Wheel Speed Sensor 
          C101C 29 [009] - Signal Implausible
          Confirmed - Tested Since Memory Clear
             Freeze Frame:
                    Fault Status: 00000001
                    Fault Priority: 2
                    Fault Frequency: 1
                    Reset counter: 76
                    Mileage: 206443 km
                    Date: 2018.01.04
                    Time 20:00:27

0086 - Rear Wheel Rear Speed Sensor 
          C101D 29 [009] - Signal Implausible
          Confirmed - Tested Since Memory Clear
             Freeze Frame:
                    Fault Status: 00000001
                    Fault Priority: 2
                    Fault Frequency: 1
                    Reset counter: 76
                    Mileage: 206443 km
                    Date: 2018.01.04

I have encoded byte26 as it was supposed to be 01010000 BUT i have not done the rest of coding for ACC.

What do i need to check? Can you please help me out?

namo, yours looks like original :)))
I will put mine sometime during the Christmas holidays. I jave also ordered the rear ABS sensors, can you help me how i should change the coding in the ABS? 

Thanks

so, i must change them ?

Hello guys,

On my car the rear ABS sensors are wht003864, do you think i have to change them for wht003864A ?

Hello,

Kneading the case with a car with KESSY with ACC. 

If you want it without KESSY with ACC then correct number should be 5E0 858 559 B 9B9

I am currently driving with the stalk control ACC được cài đặt, nhưng có thể thao tác cũ mà bị cắt ngắn. If you want and take a picture tomorrow you should cut yours in order to fit it. 

1 minutę temu, Namo napisał:

@George  i need lower plastic under ACC and without kessy. Bạn có tới số thứ tự của tôi.

I will check tomorrow evening what i have and will tell you the exact number that will fit you.

5 hours ago, Namo wrote:

A few things before I remember, the case is lower 5E0858559G9B9 là sau kessy, nhưng là một cái thường thường phải be different, soon I will know the number. The top 5E0858560C9B9 is the same in every option so you do not have to buy it.

I write in English, i read this thread with google translate :)

5E0 858559B 9B9 is the plastic for the car without KESSY. 

I went to my dealership and after the third try they gave me the correct. and can tell you the number for the one with KESSY tomorrow evening if you need it because it is not with me now. 

I know that i can't go to the dealer and retrofit ACC. I have a regular cruise control, but i have the radar in the front. Now i am looking wif with a simple encoding and steering column swap i can install ACC (up to 160 km/h is good for me).

Thanks

The car was manufactured may or August 2014. I agree that would be good to get the unlocked radar, but if the one thhat i have is working i would prefer not to spend excess 300E. How can i check, with vcds or i have to dismount it and check the number?

the steering column switches i will buy for sure. :) i guess there the easiest option is from the dealer, right?

Hi,

Thank you for the reply. My car does not have ACC, it has only the radar for city assistance and the pre-safe functions. I was wondering if i can use this radar wfor the ACC, to 160 km/h is okay for me. Is there a way that i can check if the radar that i have is good for acc?

Hello rrobert,

sorry for writing in English, but i don't know Polish. I will ask google to translate it :), this is how i've been reading. Please tell me if the retrofit was successfull? How difficult was the coding and did you need the pin code,of the car?

i have the same car, but i have the radar already factory installed.

thanks

Witam rrobert,

przepraszam za pisanie w języku angielskim, ale nie wiem, po polsku. Spytam google to przetłumaczyć :), to jak czytałem. Proszę mi powiedzieć, czy modernizacja była udana? Jak trudno było kodowanie i czy potrzebny jest kod pin, z samochodu?

mam ten sam samochód, ale mam radar już fabrycznie zainstalowany.

Thanka,