George
Użytkownik-
Posts
14 -
Joined
-
Last visited
Reputation
3 NeutralnaOctavia
-
Model
Octavia 3 Combi
-
Silnik
2.0 TDI CR CKFC
-
Skrzynia
DSG
Informacje
-
Lokalizacja
Bulgaria
Recent Profile Visitors
The recent visitors block is disabled and is not being shown to other users.
-
i have tried to do the encoding, But when i reach the ABS module i receive the following error: I have realized that i have been trying to do the coding with Byte 26 encoded to 11110000 , can this be the problem?3 If i do the rest of the encoding i get the following error in the engine: Address 01: Engine (J623-CKFC) Labels:. 04L-907-309-V1.clb Part No SW: 04L 906 021 DT HW: 04L 907 309 D Component: R4 2,0L EDC H22 8127 Revision: 83H22--- Coding: 111D001A043401091000 Shop #: WSC 02001 451 00000 ASAM Dataset: EV_ECM20TDI01104L906021DT 002008 ROD: EV_ECM20TDI01104L906021DT_002.rod VCID: 7A3EB2053FC3E65006-802E 2 Faults Found: 17149 - Check Coding of ECUs on Powertrain Data Bus P1647 00 [032] - - Intermittent - Not Confirmed - Tested Since Memory Clear Freeze Frame: Fault Status: 00000001 Fault Priority: 2 Fault Frequency: 1 Mileage: XXX km Date: 2018.01.06 Time: 16:13:00 Engine speed: 0.00 /min Normed load value: 0.0 % Vehicle speed: 0 km/h Coolant temperature: 50 °C Intake air temperature: 52 °C Ambient air pressure: 930 mbar Voltage terminal 30: 12.020 V Unlearning counter according OBD: 40 ACC variants-Bit 0: 0 CCS Switch-Bit 0: 1 Cruise control switch actuation-Bit 0: 0 Cruise control switch actuation-Bit 8: 32 ACC variants (coding)-Bit 0: 3 Acceleration: 0.000 m/sІ 4709 - No Communications with Cruise Control (Front) Distance Sensor U0235 00 [032] - - Intermittent - Not Confirmed - Tested Since Memory Clear Freeze Frame: Fault Status: 00000001 Fault Priority: 6 Fault Frequency: 1 Mileage: XXX km Date: 2018.01.06 Time: 16:12:59 Engine speed: 0.00 /min Normed load value: 0.0 % Vehicle speed: 0 km/h Coolant temperature: 50 °C Intake air temperature: 52 °C Ambient air pressure: 930 mbar Voltage terminal 30: 12.020 V Unlearning counter according OBD: 40 Drivetrain coordinator: ACC fault status-Bit 0: 0 Drivetrain coordinator: ACC fault status-Bit 8: 0 Drivetrain coordinator: brake fault status-Bit 0: 0 Drivetrain coordinator: brake function status-Bit 0: 0 Drivetrain coordinator: brake function status-Bit 8: 0 Acceleration: 0.000 m/sІ Readiness: 0 0 0 0 0
-
-
Thanks a lot!!! it worked! I coded the ABS to 11110000 and after 7-8 km. of driving it is okay. I will drive more tomorrow and check if there are errors written in the abs module. I bought sensors wht003864a from carsequipment. When i was having the fault the ABS lamp on the instrument panel was NOT on. Will the ACC run if i do all the steps without the one with ODIS ?
-
Hi guys, i have changed the rear sensors last weekend and i put the one ending on A. But i get the following fault codes: Address 03: ABS Brakes Labels: 5Q0-907-379-ESP-V1.clb Control Module Part Number: 5Q0 907 379 R HW: 5Q0 907 379 F Component and / or Version: EMB8 EHCB H31 0356 Software Coding: 1C07629124210975007D060141C4243846249000608224F0F0615070C002 Work Shop Code : WSC 73430 031 00063 ASAM Dataset: EV_Brake1UDSContiMK100ESP 033001 (SK37) ROD: EV_Brake1UDSContiMK100ESP_033.rod VCID: 4BCD144833143CC95E-801E 2 Faults Found: 0070 - Rear Left Wheel Speed Sensor C101C 29 [009] - Signal Implausible Confirmed - Tested Since Memory Clear Freeze Frame: Fault Status: 00000001 Fault Priority: 2 Fault Frequency: 1 Reset counter: 76 Mileage: 206443 km Date: 2018.01.04 Time 20:00:27 0086 - Rear Wheel Rear Speed Sensor C101D 29 [009] - Signal Implausible Confirmed - Tested Since Memory Clear Freeze Frame: Fault Status: 00000001 Fault Priority: 2 Fault Frequency: 1 Reset counter: 76 Mileage: 206443 km Date: 2018.01.04 I have encoded byte26 as it was supposed to be 01010000 BUT i have not done the rest of coding for ACC. What do i need to check? Can you please help me out?
-
-
-
-
Hello, Kneading the case with a car with KESSY with ACC. If you want it without KESSY with ACC then correct number should be 5E0 858 559 B 9B9 I am currently driving with the stalk control ACC được cài đặt, nhưng có thể thao tác cũ mà bị cắt ngắn. If you want and take a picture tomorrow you should cut yours in order to fit it.
-
-
-
-
The car was manufactured may or August 2014. I agree that would be good to get the unlocked radar, but if the one thhat i have is working i would prefer not to spend excess 300E. How can i check, with vcds or i have to dismount it and check the number? the steering column switches i will buy for sure. :) i guess there the easiest option is from the dealer, right?
-
-
Hello rrobert, sorry for writing in English, but i don't know Polish. I will ask google to translate it :), this is how i've been reading. Please tell me if the retrofit was successfull? How difficult was the coding and did you need the pin code,of the car? i have the same car, but i have the radar already factory installed. thanks Witam rrobert, przepraszam za pisanie w języku angielskim, ale nie wiem, po polsku. Spytam google to przetłumaczyć :), to jak czytałem. Proszę mi powiedzieć, czy modernizacja była udana? Jak trudno było kodowanie i czy potrzebny jest kod pin, z samochodu? mam ten sam samochód, ale mam radar już fabrycznie zainstalowany. Thanka,